Jump to content

Benoît Dautremépuis

Membre
  • Posts

    328
  • Joined

  • Last visited

  • Days Won

    19

Everything posted by Benoît Dautremépuis

  1. Tu débranche les ESC de la carte centrale (Donc je débranche tous les moteurs de la carte KK2) -Tu débranche le récepteur de la carte centrale (Tu parles du module FrSKy je suppose) -Tu branche un ESC sur la sortie de ton emetteur correspondante au gaz. (Je branche un ESC seul sur la sortie THR de la carte FrSky qui correspond aux gaz sur la Taranis ?? ) -Tu alume la radio et tu pousse le manche des gaz à fond -Tu alimente le multi (Je mets en marche le drone) Oui mais sans brancher autre chose que l'ESC à calibrer -Ton ESC va biper pour te dire qu'il à enregistré le point haut des gaz -Tu baisse les gaz au minimum et ton ESC va biper plusieurs fois en guise de confirmation -Tu débranche le multi -Tu bascule un autre ESC sur la sortie gaz et ainsi de suite pour les 4 ESC. (Même procédure pour tous)
  2. Je pencherais pour l'ESC, j'ai lu que les moteurs brushless étaient rodés sous l'eau ... (je ne sais pas si cela est vrai) Une technique pour bien sécher un multi-rotor baigneur, le riz pendant 24h
  3. Ok alors pour moi ça vient de la courbe des gaz enregistrée dans chaque ESC. Je m'explique: Les ESC doivent connaitre les points mini et maxi de ta course du manche des gaz Comment faire ? Les ESC flashés en SimonK facilite la vie: -Tu enleve les hélices -Tu débranche les ESC de la carte centrale -Tu débranche le récepteur de la carte centrale -Tu branche un ESC sur la sortie de ton emetteur correspondante au gaz. -Tu alume la radio et tu pousse le manche des gaz à fond -Tu alimente le multi -Ton ESC va biper pour te dire qu'il à enregistré le point haut des gaz -Tu baisse les gaz au minimum et ton ESC va biper plusieurs fois en guise de confirmation -Tu débranche le multi -Tu bascule un autre ESC sur la sortie gaz et ainsi de suite pour les 4 ESC. J'espère être clair
  4. Vu la faible réactivité des moteurs thermiques je doute que ce soit jouable
  5. Aucun soucis il faudra juste faire correspondre les voies du récepteur avec celles que tu vas configurer dans le modèle de la Taranis
  6. alors sur le coté du récepteur tu as un diagramme de connexion (le signal - fil blanc ou jaune correspond au signe oméga version carré, le + fil rouge sur le plus et le fil noir sur le moins) : Ensuite pour la carte centrale :
  7. Cool ! Tu vas voir la Taranis est une petite tuerie ! Je te propose un peu de lecture le temps de la recevoir https://www.dropbox.com/s/bamzh1xaugizko0/Manuel_Taranis_FR_V1.0.zip
  8. Salut, Pour commencer avec un budget de 150 euros maxi le Hubsan X4-h107d est un bon choix pour moi
  9. Arf désolé je n'ai pas trop eu le temps de me connecter dernièrement. Dommage pour la radio, personnellement je la trouve assez simple mais il faut effectivement mettre le nez dedans un minimum (comme toutes les radios, ormis celles de chez DJI mais ce sont de belles bouses à mon avis) Bref comme je disais si tu veux une radio avec un minimum de paramètres modifiables, il va falloir commencer par apprendre la logique de la radio. De mon expérience personnel, je ne peux te parler que de hitec (ayant eu la Aurora 9) ou de la Turnigy 9XR sous openRX ou la Taranis sous openRX également. Pour ses deux dernières effectivement tu es sous un soft libre et aux possibilités quasi infinies mais faut se pastiller au minimum la notice (que l'on trouve facilement traduite sur le net) Ayant la Taranis, je me demande si je ne vais pas vendre ma 9XR si ça t'intéresse j'ai peut être encore le modèle du 330 qui traine quelque part.
  10. alors déjà tu part sur un modèle type avion, après il faut faire correspondre les voies de ta radio avec celles de la carte centrale.
  11. Flash RC, FPV4ever, studio sport ... Pour le retour vidéo tu peux le brancher sur la télé oui mais le mieux étant un écran prévu pour le FPV sans bluescreen en cas de coupure du retour.
  12. Quand on sait que l'Optima 9 seul coute environ 90 euros ... Je pense que tu as fait une bonne affaire. Tu verra cette radio est super simple J'ai reçu ma Taranis ce matin ... Déjà moins facile lol mais je sent que je vais m'éclater !
  13. J'ai commencé avec ceste radio, elle est géniale ! grand écran tactile, réglages faciles et télémétrie. Seul hic regarde le prix des récepteurs ... Si tu n'a pas plusieurs modèles c'est bien mais quand il faut acheter des Rx en plus, ça pique un peu je trouve...
  14. Bonjour Pour le Naza et la Zenmuse pas de soucis mais fait gaffe au matériel FPV, généralement c'est à alimenter en 12V
  15. Oui c'est compatible c'est ce que j'avais avant dans ma 9XR avant de mettre le module interne. La 9X c'est quasiment la même chose sauf qu'ils ont amélioré les manches, mis un rétro-eclairage et tu peux la flasher via la prise AVR sur la 9XR. Une petite photo du dos de la 9XR avec le module que je t'ai linké :
  16. Ici avec un récepteur, en France : http://www.ladroneshop.com/fr/radios-rc/630-module-rf-frsky-djt-24ghz-combo-pack-avec-telemetry-module-v8fr-ii-rx.html
  17. Mieux vaut prendre le XJT (le dernier en date) dispo en france ici :http://www.intermodel.fr/modules-24-ghz/2025-module-xjt-s-port-816-voies-telemetrie-compatible-taranis-graupner-jr.html?&sfs=&icn=89 La Taranis je l'ai prise sur HK à 172$ auxquels il faut rajouter 4$ pour le chargeur europe: http://www.hobbyking.com/hobbyking/store/__45025__FrSky_2_4GHz_ACCST_TARANIS_X9D_Digital_Telemetry_Radio_System_Mode_1_.html
  18. Tout à fait tu peux prendre une Turnigy 9X ou une 9XR et un module Frsky de type JR qui se "clips" à l'arrière de la radio. Aucune soudure c'est du plug and play Ou alors prendre une Taranis direct
  19. Pour ma part je vol avec une Turnigy 9XR avec un module Frsky interne, et la je viens de me commander une Taranis (X9D) Les retours ont l'air très satisfaisants, j'ai hâte de la recevoir !
  20. http://www.studiosport.fr/molette-controle-tilt-zenmuse-pour-dji-phantom-p-2909.html
  21. Salut, A priori sur ce récepteur le failsafe n'est disponible que sur la voie 3 (Gaz) alors que le Naza détecte la perte radio avec un déclenchement de failsafe sur son entrée U. J'ai trouvé un article (en anglais) d'un mec qui propose une configuration qui semble fonctionné: I wrote this guide to help others in the same situation as me. I hope it will help others. The Futaba R617FS receiver only support failsafe on channel 3, if you followed the Naza manual, you won’t be able to setup the failsafe for signal loss. My setup being a Futaba T7C Tx with a Futaba R617FS Rx, I was struggling to setup the failsafe to work on signal loss, and searching around the internet, I saw a lot of peoples asking how to set it up, and no answers, often the replies were as simple as “that can’t be done with this Rx”. I finally found the solution and will try to explain it here for everyone else. Facts: a) The R617FS receiver only supports failsafe on channel 3 (throttle) The Naza-M gyro only supports getting a failsafe signal from channel U c) If you follow the Naza-M manual, you have connect your rx channel 3 (throttle) to your naza channel T (throttle) and rx channel 5 (3 way switch) to your naza channel U (“GPS/Manual/Failsafe” command switch channel) d) Combining point a, b and c, you’ll never be able to get the fail safe working when losing radio signal Solution: To sum it up, you need to have your rx channel 3 (which support the failsafe) to your naza channel U, your rx channel 6 (pitch) to your naza channel T, you set up your TX for Heli mode, Swash type H-1, and use the pitch curve to control your throttle and the throttle curve to control the flight mode (using a flat line in each switch position to toggle to GPS/Attitude/Manual mode). This manual will guide you to the complete setup of your Futaba T7C / R617FS / Naza-M to take the full advantage of every option the Naza-M + GPS give you, setup the fail-safe on signal loss, setup the switches to toggle between each flight mode, each IOC mode and a manual fail-safe switch. Step By Step Instructions: (I use the Futaba T7C HELI-Mode2 Tx, instructions may differ a bit with other radios) 1- Connect your receiver to your Naza-M as follow: R617FS ---> NAZA-M Channel 1 ---> A (same as manual) Channel 2 ---> E (same as manual) Channel 3 ---> U (different from manual) Channel 4 ---> R (same as manual) Channel 5 ---> X1 (different from manual) Channel 6 ---> T (different from manual) Channel 7 ---> X2 (same as manual) 2- Go in your Tx, make a new model or use the one you already have 3- The Tx Basic menu PARAMETER: a- In your Tx, go to menu “PARAMETER”, go on RESET>EXEC and hold the dial button until it reset (you want to reset to make sure no other settings will interfere with the setup) b- Scroll down to TYPE and select H-1 c- Scroll down to CH5-SW> and chose - d- Scroll down to CH7-SW> and chose B (I use switch B to toggle the IOC) 4- The Tx Basic menu “REVERSE” Menu: a- Here’s how I have mine setup, I suggest you follow the same pattern so it’s easier to follow the guide, Reverse CH1, CH4 and CH7, keep all others in NOR5- The Tx Basic menu “TIMER”, Set TIMER to ON or OFF, assign Switch D(Down), set timer to your flight time, and mode UP or DOWN according to your preference (I use UP mode) 6- The Tx Basic Menu “TH-CUT”, Set TH-CUT> to INH 7- The Tx Advanced Menu “HOV-THR”, Set HOV-THR to INH 8- The Tx Advanced Menu “HOV-PIT”, Set HOV-THR to INH 9- The Tx Advanced Menu “GYRO”, Set GYRO to INH (more on this later) Now the pre-setup of the Tx is Ready, now we need to run the Naza application and connect the USB to the Naza to complete the setup 10- In Naza application, Tx Cali Page, Make sure all 4 channel are set to REV (if you follow the same channel reversing as me in the Tx of course), verify all channel are moving in appropriate direction, also you’ll want to calibrate here 11- Programming the 3 way switch for GPS/Attitude/Manual mode a- Go in Tx Advanced Menu “THR-CRV” b- Place your 3-way switch to normal and set the normal throttle curve 8% on all points, in the application you should now have the GPS mode turn Blue, if not, change the value till GPS turn Blue, make sure you use the same value on all point (flat line) c- Place your switch to Idle1 and set the Idle1 throttle curve to 50% on all points, in application, you should now have the attitude mode Blue d- Place your switch to Idle2 and set the Idle2 throttle curve to 90% on all points, in application, you should now see that manual is turn Blue (again, this value may be different for you, if manual don’t turn Blue, adjust the value as needed) e- Your 3-way switch is now set 12- Programming a manual Fail-Safe switch using the TH-Hold Switch a- Flip the TH-Hold switch in TH-Hold position (toward you) b- Go in Tx advanced menu “TH-HOLD” and set POS to +40% c- In application, you should now see that Fail-Safe is turn Blue, if not, adjust the value of POS till you have Fail-Safe turn Blue d- Now, you can use the TH-Hold as a Return to Home (RTH) switch (for RTH, make sure that in application autopilot page, that you have check Go-Home and Landing, otherwise your Fail-Safe will only land) 13- Setting the Fail-Safe on loss of signal a- Have your TH-Hold switch ON and make sure in the application that Fail-Safe is Blue b- Go in Tx Basic Menu “FAIL SAFE” c- Make sure that CH: 3 is set to F/S, you should have the number 3 flashing on the Tx screen, press and hold the Tx dial button until you hear 2 fast beep, when you hear the beeps, this mean that fail safe position is saved in Rx d- Now we need to test the fail safe and make sure it works, place the TH-Hold switch to OFF, now in application you should have either GPS/A/M in Blue, Power OFF the Tx, now Fail Safe should turn blue and you have your fail safe set for loss of signal/Tx, power back on the Tx and the Naza should go back to whatever mode you have your 3-way switch at 14- Setting the Intelligent Orientation Control (IOC) a- Go in application Autopilot Page b- Make sure to check “3. Intelligent Orientation Control” c- On Tx, Place switch A and B to UP position d- Go in Tx advanced menu “P-MIX1” e- Set MAS to OFS f- Set SLV to CH7 g- Set SW to A-UP h- Set RT to -100% i- How it work: Switch A will control what IOC mode you want (UP for Course Lock and DOWN for Home Lock) and switch B will control if IOC is OFF or ON (UP is IOC OFF, DOWN is IOC ON) j- Test your IOC Switches, when B is UP IOC is always OFF, you can move switch A UP or DOWN and this won’t change anything, but when you switch B to DOWN, IOC will switch to whatever mode you set A switch to 15- Only thing left is the Gimbal X1 Channel, I don’t use this feature so I haven’t played with it, but the X1 channel is linked to your GYRO channel, if you use this feature, you can use the Tx GYRO menu to control the X1 channel or you can set a switch for it from the PARAMETER menu This is it, if you followed this guide to the letter, you’ll be able to switch to all flight mode, have a switch for Return to Home, have a functional Fail-Safe in case of loss of signal/Tx, and have the ability to use any IOC mode the Naza-M have Here is a summary of all the switches and their functions: Switch E (3-way switch): Normal position = GPS Mode, Idle1 = Attitude Mode, Idle2 = Normal Mode Switch A: UP = IOC Mode Course Lock, DOWN = IOC Mode Home Lock Switch B: UP = IOC Mode is OFF, DOWN = IOC Mode is ON (to whatever switch A is at) Switch D: UP = Timer OFF, DOWN = Timer ON Switch G (TH-HOLD): UP (away from you) = Fail-Safe OFF, DOWN (toward you) = Fail-Safe ON (RTH)
  22. Avec de tels moteurs il va te falloir des lipos en 6 éléments et des hélices de 14 ou 15 pouces. Pour embarquer une gopro cela fait un peu riche je pense.
  • votre-publicite-ici-lyon.png

×
×
  • Create New...